{"title":"LCDs \u0026 Displays","description":"\u003cp\u003eBrowse our LCDs \u0026amp; Displays collection. New Arrival.\u003c\/p\u003e","products":[{"product_id":"monochrome-154-128x64-oled-graphic-display-module-kit-discontinued","title":"Monochrome 1.54\" 128x64 OLED Graphic Display Module Kit [Discontinued]","description":"\u003cp\u003eDiscontinued - \u003cb\u003eyou can grab \u003c\/b\u003eMonochrome 1.3\" 128x64 OLED graphic display - STEMMA QT \/ Qwiic\u003cb\u003e instead! \u003c\/b\u003e\u003c\/p\u003e\u003cp\u003eIf you've been diggin' our monochrome OLEDs but need something bigger, this display will delight you! These displays are \u003cstrong\u003e1.54\" diagonal\u003c\/strong\u003e, and very readable due to the high contrast of an OLED display. This display is made of \u003cstrong\u003e128x64 individual white OLED pixels,\u003c\/strong\u003e each one turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this graphic display for its crispness!\u003c\/p\u003e\u003cp\u003eThe driver chip, \u003cstrong\u003eSSD1305 can communicate in three ways\u003c\/strong\u003e: 8-bit, I2C or SPI. Personally we think SPI is the way to go, only 4 or 5 wires are required and its very fast. The OLED itself requires a 3.3V power supply and 3.3V logic levels for communication. We include a breadboard-friendly level shifter that can convert 3V or 5V down to 3V, so it can be used with 5V-logic devices like Arduino.\u003c\/p\u003e\u003cp\u003eThe power requirements depend a little on how much of the display is lit but on average the display uses about 50mA from the 3.3V supply. Built into the OLED driver is a simple switch-cap charge pump that turns 3.3V into a high voltage drive for the OLEDs.\u003c\/p\u003e\u003cp\u003eEach order comes with one assembled OLED module with a nice bezel and 4 mounting holes. The display is 3V logic \u0026amp; power so we include a HC4050 level shifter. We also toss in a\u003cstrong\u003e \u003c\/strong\u003e220uF capacitor\u003cstrong\u003e,\u003c\/strong\u003e as we noticed an Arduino may need a little more capacitance on the 3.3V power supply for this big display! This display does not come with header attached but we do toss in a stick of header you can solder on. Also, the display may come in SPI mode or 8-bit mode. You can change modes from 8-bit to SPI or I2C with a little soldering, check out the tutorial for how to do so.\u003cstrong\u003e Please Note\u003c\/strong\u003e: Metro not included! A microcontroller such an Arduino is required to use.\u003c\/p\u003e\u003cp\u003eGetting started is easy! We have a detailed tutorial and example code in the form of an Arduino library for text and graphics. You'll need a microcontroller with more than 512 bytes of RAM since the display must be buffered. The library can print text, bitmaps, pixels, rectangles, circles and lines. It uses 512 bytes of RAM since it needs to buffer the entire display but its very fast! The code is simple to adapt to any other microcontroller.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\u003ch2\u003eTechnical Details\u003c\/h2\u003e\u003cdiv id=\"tab-technical-details-content\" class=\"panel-collapse collapse in\"\u003e \u003cdiv class=\"row\"\u003e \u003cdiv class=\"col-lg-12 col-md-12 col-sm-12 col-xs-12\"\u003e\n\u003cul\u003e\n\u003cli\u003e\nDatasheet for SSD1305, the passive OLED driver chip in the module this is the chip in the module that converts SPI\/8-bit commands to OLED control signals\u003c\/li\u003e\n\u003cli\u003ePCB Dimensions: 39.5mm x 57.6mm x 1.1mm \/ 1.55\" x 2.27\" x 0.04\"\u003c\/li\u003e\n\u003cli\u003eScreen Dimensions: .71\" x 1.4\" x .29\" \/ 18.2mm x 35.8mm 7.6mm\u003c\/li\u003e\n\u003cli\u003eScreen Weight: 15g\u003c\/li\u003e\n\u003cli\u003eDriving voltage: 2.8-3.3V\u003c\/li\u003e\n\u003cli\u003eInterface: 8 parallel port, 3\/4-wire SPI, I2C\u003c\/li\u003e\n\u003cli\u003eDiagram for 1.54 OLED submodule\u003c\/li\u003e\n\u003cli\u003eDatasheet for the 1.54\" OLED display\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eProduct Weight: 15.0g \/ 0.5oz \u003c\/p\u003e\n\u003c\/div\u003e \u003c\/div\u003e\n\u003cul id=\"product-files\"\u003e \u003c\/ul\u003e \u003cdiv class=\"row\"\u003e\n\u003cdiv class=\"col-lg-2 col-md-3 col-sm-3 col-xs-4\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"col-lg-2 col-md-3 col-sm-3 col-xs-4\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e \u003c\/div\u003e","brand":"Adafruit","offers":[{"title":"Default Title","offer_id":51290332430372,"sku":"xda1787257462157","price":21.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0725\/0729\/3732\/files\/monochrome-154-128x64-oled-graphic-display-module-kit-discontinued_1.jpg?v=1787257466"},{"product_id":"monochrome-242-128x64-oled-graphic-display-module-kit","title":"Monochrome 2.42\" 128x64 OLED Graphic Display Module Kit","description":"\u003cp\u003eIf you've been diggin' our monochrome OLEDs but need something bigger, this display will delight you! These displays are \u003cstrong\u003e2.42\" diagonal\u003c\/strong\u003e, and very readable due to the high contrast of an OLED display. This display is made of \u003cstrong\u003e128x64 individual white OLED pixels,\u003c\/strong\u003e each one turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this graphic display for its crispness!\u003c\/p\u003e\u003cp\u003eThe driver chip, \u003cstrong\u003eSSD1305 can communicate in three ways\u003c\/strong\u003e: 8-bit, I2C or SPI. Personally we think SPI is the way to go, only 4 or 5 wires are required and its very fast. The OLED itself requires a 3.3V power supply and 3.3V logic levels for communication. We include a breadboard-friendly level shifter that can convert 3V or 5V down to 3V, so it can be used with 5V-logic devices like Arduino.\u003c\/p\u003e\u003cp\u003eThe power requirements depend a little on how much of the display is lit but on average the display uses about 50mA from the 3.3V supply. Built into the OLED driver is a simple switch-cap charge pump that turns 3.3V into a high voltage drive for the OLEDs.\u003c\/p\u003e\u003cp\u003eEach order comes with one assembled OLED module with a nice bezel and 4 mounting holes. The display is 3V logic \u0026amp; power so we include a HC4050 level shifter. We also toss in a\u003cstrong\u003e \u003c\/strong\u003e220uF capacitor\u003cstrong\u003e,\u003c\/strong\u003e as we noticed an Arduino may need a little more capacitance on the 3.3V power supply for this big display! This display does not come with header attached but we do toss in a stick of header you can solder on. Also, the display may come in SPI mode. You can change modes from 8-bit to SPI or I2C with a little soldering, check out the tutorial for how to do so.\u003cstrong\u003e Please Note\u003c\/strong\u003e: Metro not included! A microcontroller such an Arduino is required to use.\u003c\/p\u003e\u003cp\u003eGetting started is easy! We have a detailed tutorial and example code in the form of an Arduino library for text and graphics. You'll need a microcontroller with more than 512 bytes of RAM since the display must be buffered. The library can print text, bitmaps, pixels, rectangles, circles and lines. It uses 512 bytes of RAM since it needs to buffer the entire display but its very fast! The code is simple to adapt to any other microcontroller.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e Cable and code on back of board may vary but displays will work the same.\u003c\/p\u003e\u003cp\u003ePlease note that OLED displays are made of hundreds of...OLEDs! That means each pixel is a little organic LED, and if its kept on for over 1000 hours it'll start to dim. If you want to keep the display uniformly bright, please turn off the display (set the pixels off) when it isn't needed to keep them from dimming.\u003c\/p\u003e\u003cp\u003e\u003c\/p\u003e\u003ch2\u003eTechnical Details\u003c\/h2\u003e\u003cdiv id=\"tab-technical-details-content\" class=\"panel-collapse collapse in\"\u003e \u003cdiv class=\"row\"\u003e \u003cdiv class=\"col-lg-12 col-md-12 col-sm-12 col-xs-12\"\u003e\u003cul\u003e\n\u003cli\u003e\nDatasheet for SSD1305 the passive OLED driver chip in the module this is the chip in the module that converts SPI\/8-bit commands to OLED control signals\u003c\/li\u003e\n\u003cli\u003eScreen Dimensions: 1.14\" x 2.2\" x .26\" \/ 29mm x 56mm x 6.8mm\u003c\/li\u003e\n\u003cli\u003eScreen Weight: 22g\u003c\/li\u003e\n\u003cli\u003eDriving voltage: 3.3V\u003c\/li\u003e\n\u003cli\u003eInterfaces: 8 parallel port, 4-wire SPI, I2C\u003c\/li\u003e\n\u003cli\u003eDiagram for 2.42\" OLED submodule\u003c\/li\u003e\n\u003cli\u003eDatasheet for the 2.42\" OLED display\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/div\u003e \u003c\/div\u003e\n\u003cul id=\"product-files\"\u003e \u003c\/ul\u003e \u003cdiv class=\"row\"\u003e\n\u003cdiv class=\"col-lg-2 col-md-3 col-sm-3 col-xs-4\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"col-lg-2 col-md-3 col-sm-3 col-xs-4\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e \u003c\/div\u003e","brand":"Adafruit","offers":[{"title":"Default Title","offer_id":51290332528676,"sku":"qil1787257463249","price":26.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0725\/0729\/3732\/files\/monochrome-242-128x64-oled-graphic-display-module-kit_1.jpg?v=1787257467"},{"product_id":"monochrome-23-128x32-oled-graphic-display-module-kit","title":"Monochrome 2.3\" 128x32 OLED Graphic Display Module Kit","description":"\u003cdiv class=\"col-lg-2 col-md-3 col-sm-3 col-xs-4\"\u003e\u003cem\u003e\u003cstrong\u003eThis 2.3\" 128×32 blue OLED is crisp, high-contrast, and needs no backlight. It uses the SSD1305 driver with 8-bit, I2C or SPI, runs at 3.3V (level shifter included), and draws about 50mA. Requires \u0026gt;512B RAM for buffering.\u003c\/strong\u003e\u003c\/em\u003e\u003c\/div\u003e\n\u003chr\u003e\n\u003cp\u003eIf you’ve been enjoying monochrome OLEDs but want something a little bigger, this 2.3\" OLED display is a great upgrade. It’s easy to read thanks to OLED’s naturally high contrast, and it uses 128 × 32 blue pixels, with each pixel individually switched on or off by the onboard controller. Since the display produces its own light, there’s no backlight, which helps keep power use down while giving that crisp, high-contrast look OLEDs are known for.\u003c\/p\u003e\n\u003cp\u003eThe display uses the SSD1305 driver chip, which supports 8-bit, I2C, or SPI communication. SPI is often the simplest option, using only 4 or 5 wires and offering fast updates. The OLED runs from a 3.3V power supply and expects 3.3V logic levels, but a breadboard-friendly level shifter is included so it can be used with both 3V and 5V systems, including 5V boards like Arduino.\u003c\/p\u003e\n\u003cp\u003ePower draw depends on how much of the screen is lit, but it typically uses around 50mA from the 3.3V supply. The driver includes a built-in boost converter that steps 3.3V up to the higher voltage needed to run the OLED pixels. This boost circuit can sometimes cause a squeaking or buzzing sound, which you may be able to reduce by adding hot glue or foam tape around the inductor, although it may not be completely removable.\u003c\/p\u003e\n\u003cp\u003eEach order includes one assembled OLED module with a bezel and four mounting holes for easy fitting. Because the display is 3V logic and power, it comes with an HC4050 level shifter, plus a 220µF capacitor — useful because some Arduino setups may need a little extra capacitance on the 3.3V rail for a display this size. The header is not pre-soldered, but a strip of header is included for you to attach. The display may arrive set to 8-bit mode, and you can switch it to SPI or I2C with a small soldering change (the tutorial explains how).\u003c\/p\u003e\n\u003cp\u003eGetting started is straightforward with a detailed guide and Arduino library examples for text and graphics. Since the display must be buffered, you’ll need a microcontroller with more than 512 bytes of RAM. The library supports drawing text, bitmaps, pixels, rectangles, circles, and lines, and uses 512 bytes of RAM to buffer the full display while staying fast and easy to adapt to other microcontrollers.\u003c\/p\u003e\n\u003cp\u003ePlease note that OLED displays are made from lots of tiny organic LEDs. If pixels are left on continuously for over 1000 hours, they can start to dim. To keep brightness even over time, it’s best to turn off the display (set pixels off) when it isn’t needed.\u003c\/p\u003e\n\u003cp\u003e\u003ciframe width=\"560\" height=\"315\" src=\"https:\/\/www.youtube.com\/embed\/ov591MtLIY4?si=I9c5yeYN85AJ6nci\u0026amp;start=197\" title=\"YouTube video player\"\u003e\u003c\/iframe\u003e\u003c\/p\u003e\n\u003ch2 class=\"col-lg-2 col-md-3 col-sm-3 col-xs-4\"\u003eSpecifications\u003c\/h2\u003e\n\u003cdiv class=\"col-lg-2 col-md-3 col-sm-3 col-xs-4\"\u003e\n\u003cul\u003e\n\u003cli\u003eScreen Dimensions: 64mm x 28mm x 5mm\u003c\/li\u003e\n\u003cli\u003ePCB Dimensions: 66.5mm x 35mm x 3mm\u003c\/li\u003e\n\u003cli\u003eWeight: 18g\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003ch2 class=\"col-lg-2 col-md-3 col-sm-3 col-xs-4\"\u003eResources\u003c\/h2\u003e\n\u003cdiv class=\"col-lg-2 col-md-3 col-sm-3 col-xs-4\"\u003e\n\u003cul\u003e\n\u003cli\u003eDatasheet for SSD1305\u003c\/li\u003e\n\u003cli\u003eMechanical specifications\u003c\/li\u003e\n\u003cli\u003eLearn\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003ePackage Contents\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e1x Monochrome 2.3\" 128x32 OLED Graphic Display Module Kit\u003c\/li\u003e\n\u003cli\u003e1x 220uF capacitor\u003c\/li\u003e\n\u003cli\u003e1x 36-pin header\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Adafruit","offers":[{"title":"Default Title","offer_id":51290332626980,"sku":"pfi1787257464511","price":24.96,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0725\/0729\/3732\/files\/monochrome-23-128x32-oled-graphic-display-module-kit_1.jpg?v=1787257468"}],"url":"https:\/\/www.cozyharvest.shop\/collections\/lcds-displays.oembed","provider":"My Store","version":"1.0","type":"link"}